Skip to content

Country

PERDIX VHF Transmitter Circuit Boards - Integrated Antenna

by PERDIX
SKU 18510

Whether for tracking wildlife or used for security of remote equipment, our VHF transmitter circuit boards with integrated antenna just require a battery to start transmitting. Our transmitters are easily turned on and off using a small magnet and also include an activity sensor as standard. Small and lightweight - only 35mm x 55mm and 3.9 g. These boards accept batteries to allow them to transmit continuously for up to 650 days. Available in many frequencies in 150, 151 and 173 MHz ranges.

We do not sell our transmitters boards directly from our website so please contact us to order or discuss your requirements further.

 Since launching, our 20 and 25mm diameter circuit boards have been used around the world to successfully track both wildlife and equipment.  We have found, however, that many projects require the antenna to be incorporated within the housing to prevent damage to the antenna or reduce visibility. We have therefore developed a VHF transmitter board that has an antenna integrated into the PCB board.

Transmitter design


PERDIX integrated antenna VHF transmitters are built using a 35mm x 55mm rectangular single-sided PCB board. The board also has two 2.5 mm holes to allow the board to be fixed using small bolts or screws if required.

How it works


The PERDIX transmitter consists of an OOK modulated crystal Oscillator and frequency multiplier with two stage RF filter and antenna matching. It has a processor which controls the main functions of the transmitter. Activity monitoring is achieved by the use of an omnidirectional tilt and vibration sensor, this senses movement regardless of orientation of the transmitter. A magnetically operated switch is used to turn the transmitter on and off. By placing a small magnet that requires close to the unit the transmitter is activated or deactivated. No visual indication of the unit being on or off is provided as this would consume extra power and therefore shorten the battery life.  A VHF tracking receiver should therefore be used to confirm if the transmitter is activated.

Standard transmitter settings


The transmitter has two predefined modes, mode 1 is normal mode and transmits a single 17.5 mS RF pulsed carrier and is repeated every 1.6 seconds. Mode 2 is controlled by the activity sensor which is activated when the predetermined activity timer has been exceeded, typically this is 18 hours.  When there has been no movement during this time period, mode 2 is then activated. This gives two 17.5 mS transmitter pulses separated by 150mS to produce a “double beep” on the VHF receiver and is repeated every 1.5 seconds. If any activity is detected when in mode 2, the 18 hour counter is reset and the transmitter returns to mode 1. The TX power of this transmitter is 4.9 mAh.

Battery type and life


The PERDIX integrated antenna VHF transmitter boards have been designed so that a range of coin cells can be easily attached. These include Panasonic lithium cells, CR2025/HFN (165 mAh, 2.5 g), CR2032/HFN (225 mAh, 3.0 g), CR2354/HFN (560 mAh, 6.0 g) and CR2477/HFE (1000 mAh, 10.5 g). To give an idea of battery life, a CR2477 would provide a battery life of 650 days. Please note that battery life can vary depending on environmental conditions.

Transmitter frequencies


Currently we have frequencies available in 150, 151 and 173 MHz ranges.

Can any of the settings be changed?


Although the settings cannot be changed by the user, we are able to adjust some of the parameters during manufacturing to meet a particular projects needs (MOQ applies). These include the non-activity period (1.5 seconds to 30 days) and pulse spacing. Please contact us to discuss your requirements further.

 

Brand
PERDIX

Transmitter
OOK modulated crystal Oscillator and frequency multiplier with two stage RF filter and antenna matching.

Frequency range
150, 151 & 173 MHz. Others available on request.

Weight
3.9 g

Size
35mm x 55mm

Antenna
Integrated into PCB

Activation
On / Off switching by touching with magnet.

Pulse spacing
Standard: 1.6 seconds
Can be adjusted depending on range and battery life requirements.

Activity timer
Standard: 18 hrs
Timer can be adjusted depending on project requirements.

TX supply current
4.9 mAh

Spurious emissions
> -40 dBm (Meets EN300-220)

Adjacent channel TX power
> -50 dBc (Meets EN300-220)

Frequency accuracy
Typical: 0 kHz
Minimum: -2.5 kHz
Maximum: +2.5 kHz
(Meets EN300-220)

Operating temperature
-20 C to +55 C

Storage temperature
-30 C to +70 C

Supply voltage
Typical: 3 V
Minimum: 2 V
Maximum: 3.5 V

Recommended batteries
Panasonic CR2025/HFN: 3 V, 165 mAh, 2.5g.
Panasonic CR2032/HFN: 3 V, 225 mAh, 3.0g.
Panasonic CR2354/HFN: 3 V, 560 mAh, 6.0g.
Panasonic CR2477/HFE: 3 V, 1000 mAh, 10.5g.

Battery life
Up to 650 days